Toll Free (877) 302-9288

This kit contains an assortment of shims that you can insert behind the crank bearings and eliminate the end-play that causes so much excess wear on the engine components. The kit includes two .1mm and one each .2mm and .3mm shims. $6.00 for the kit. Order part number 43019.

With Cannondale engines increasing in displacement and power, we discovered that nothing has been done to help the clutch get the power out to the wheels. We've had these springs specially made to address this issue. Each spring averages eight pounds stronger than the original - adding almost fifty more pounds of force to the clutch stack! The best part is our pricing. Cannondale springs used to sell for about $9.00 each. We will sell you a complete set (6) of these new springs for only $18.00. Order part number 5001924.

These intake valves have been totally redesigned to raise the performance of your engine. They are re-desigend on top to allow better flow of air/fuel into the cylinder, and the bottom of the valve is no longer convex (as on all the factory valves). This will help increase compression by eliminating this extra room in the head. NOTE: This is NOT a drop-in item. The intake valve seats will have to be re-shaped to allow these valves to seat properly. Price: $110.00 per pair. Ordes part number 42334.

Engineers at Cannondale discovered that if the regular velocity stack was removed from the ATVs and replaced with the one from the motorcycle; there was a two horsepower increase in power! This kit contains everything you'll need to make this conversion. Cheapest horsepower you'll ever find! $22.95 for the kit. Order part number 44001.

We've located the last of the original, factory, a-arm bushings. Cannondale used to sell them for over $8.00 each! Our price, while they are still available: $0.75 each, or only $12.00 for the full set of 16 (needed to do a complete change-out on your quad). Part No. 6000152.

(For ATV) Everyone knows that Galfer manufactures the best braking components in the industry. We've made special arrangements with them to make their patented Wave Rotors available to the Cannondale community. These rotors are surplus parts that had been manufactured for the Cannondale factory. They are being made available at liquidation prices. When the supply is gone, they won't be available again. Since brake rotors are a wear item, our advice is to purchase a set while you can so you have them when your existing rotors wear out. The rotors have been "on sale" by our competitors for as low as $70.00 EACH. We are making the entire SET (2 fronts and one rear) available to you for only $110.00! Part No. 41034.

These are the same high-quality filters, from the same manufacturer, that you have been using. The only difference is the price – We ordered a few thousand of them, so we can pass the savings on to you. Our price to you is only six bucks per filter, or you can purchase a 20-pack for only $5 per filter. Part No. 5001740.

You all know what happens if dirt gets into your engine! If you use No-Toil filters, you can rest assured that dirt and dust won't be getting in through the intake. Sold in pairs - so you can always have a backup ready to go. If you don't need two, find a friend and split the order. You won't find this great product at a lower price anywhere! $34.95/pair. Part No. 40205.

You will not find this three-part kit cheaper anywhere. Each kit contains 16 ounces of biodegradable cleaner, 16 ounces of filter oil, and a tube of sealing grease for the filter rims. This will work with any foam type air filter that uses an air filter oil. It works especially well with the No Toil filters. $13.95/kit. Part No. 43006.

These high-quality tie rod ends have been designed to hold up under the worst conditions. The carbon fiber packing prevents the entry of mud, water, sand and dust much better than conventional nylon packings. Since the packing is self-lubricating, there is no need to grease the ends. Replacing the OEM ends with these will improve the feel of your steering and simplify your maintenance. $38/set of 4. Part No. 40695.

This harness addition addresses many of the problems that have plagued the electrical systems of the quads. This harness has been beautifully crafted using only the highest-quality materials, to provide the utmost in durability and reliability. One of the best changes is the inclusion of relays that allows full voltage from the battery to reach the fuel pump and fan, allowing them to run at full capacity, while still being controlled by the ECM. These relays are also individually fused to protect the ECM in the event of a failure of either the fan or fuel pump. The harness also eliminates many of the "mystery" electrical leaks that cause batteries to drain when not in use. Because we feel that the installation of this upgrade is so important for your continued satisfaction with your quad, we have decided to make it available to our customers at only a few dollars above our cost! Reduced to $99.80/each. Part No. 43005.

Yes, they are made of steel. That's why they are better! You'll never strip out the head with your wrench. More important, being made of steel, the plug won't 'weld' itself to your aluminum case - as happens with aluminum - causing the plug to seize inside the case. The mouth of the filter hole is chamfered to help align the filter during installation. Now some fear that the steel will strip out the threads of the case. This will only happen if you try and wrench the plug down the same way you do your lug nuts! Use a little care - and the extra-thick copper seating washer we also provide - and you'll never have a problem. $13.95/each. Part No. 42404.

Blackwidow takes pride in distributing the high-performance piston kits manufactured by Wade Wilcox Engineering. The three versions of the kit allow Cannondale owners a wide choice of options based on their riding styles and performance requirements.
95mm Kit - Replaces the factory piston and sleeve and allows for greater reliability and moderate performance gains while keeping costs under control. Price: $415.00 for the complete kit. Part No. 43023.
Race 450 Kit - Designed for maximum performance without exceeding the 450cc displacement limit. Price: $610.00 for the complete kit. Part No. 43024.
Race 460 Kit - When the need for speed is the only goal, this kit will provide it! Price: $685.00 for the complete kit. Part No. 43025. A technical sheet comparing the features, materials and quality of these WWE kits can be downloaded from the "Downloads" page.

The mold that once produced the magnesium valve covers has been modified and is now be producing the same part made from pure aluminum. Cannondale owners will now be able to use whatever coolant they desire, without fear of corrosive reactions with the valve cover! $139.00/each. Part No. 40496.

The majority of the Cannondale quads were sold with rubber rear brake lines as standard equipment. After years of use in this high-heat, high-stress location, they are probably due to be changed. We have worked a special deal with Streamline Performance Braking to bring you a STAINLESS STEEL replacement brake line. Our arrangement allows us to sell you this high-quality part at 25% below retail! $19.95/each. Part No. 6001036.

This is a cool little device that helps the fuel tank breathe properly, while eliminating the big ugly hose attached to the fuel cap. We've used these for over two years now and they work great (especially if you get upside down!) Available in: Red, Silver, Gold, Black, Orange and Blue. Please specify color when you order. $12.95/each. Part No. 43004.

This wrench is a copy of the tool used at the Cannondale Factory, which allows you to easily adjust your clutch without having to try and jam screwdrivers into the clutch hub, or use other makeshift methods. Precision laser cut and powder-coated. $22.95/each. Part No. 43001.

We've had these custom made by AC Racing to our specifications. Instead of mounting to the cradle bolts, the nerf bar is secured through the tube in the frame intended for the OEM bars. A much safer and stronger mounting point. Since we are purchasing directly from the manufacturer, we can offer this high-quality product for about the same price as the regular nerf bars. Unlike the OEM bars, these Pro-Pegs have been fitted to allow the use of 22" rear tires for desert racing. These bars can be mounted to older frames that have the plugged off tube ends. Let us know and we will ship the bars with a modified adapter for this purpose. You can choose either red, black or blue netting. Specify color when ordering. $219.00/each. Part No. 43009.